VMware VCENTER APPLICATION DISCOVERY MANAGER 6.1 - REPOSITORY Manual de usuario Pagina 151
- Pagina / 220
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
OneCommand™ Manager Application P007997-01A Rev. B
8. Managing Adapters and Ports
NIC
151
LLDP Settings Area
Transmit Enabled – LLDP Transmit can be enabled or disabled.
Transmit Port Description Enabled – Provides a description of the port in an
alpha-numeric format. The value equals the ifDescr object, if the LAN device
supports RFC 2863.
Transmit System Name Enabled – Provides the system's assigned name in an
alpha-numeric format. The value equals the sysName object, if the LAN device
supports RFC 3418.
Receive Enabled – LLDP Receive can be enabled or disabled.
Transmit System Description Enabled – Provides a description of the network
entity in an alpha-numeric format. This includes the system's name and
versions of hardware, operating system and networking software supported by
the device. The value equals the sysDescr object, if the LAN device supports
RFC 3418.
Transmit System Capabilities Enabled – Indicates the primary function(s) of the
device and whether or not these functions are enabled on the device. The
capabilities are indicated by two octets. Bits 0 through 7 indicate Other,
Repeater, Bridge, WLAN AP, Router, Telephone, DOCSIS cable device and
Station respectively. Bits 8 through 15 are reserved.
PFC Priorities Area
Active Priorities – The priorities that are marked active for PFC.
Enable – When checked, PFC is enabled.
Configured Priorities – The priorities that are configured, but might not yet be
active. A maximum of two PFC priority check boxes can be selected, out of
which one of them must match the iSCSI priority. The additional PFC priority
would be for the Ethernet traffic. This additional PFC priority must be assigned
to a priority group which has no other priorities.
ETS Priority Groups Area
Active Groups
Group ID – The Priority Group ID.
Priority Membership – The different priorities that are assigned to the
various Priority Groups. This is the currently active configuration.
Bandwidth % – The bandwidths that are assigned to different Priority
Groups. This is the currently active configuration.
Configured Groups
Group ID – The Priority Group ID.
Priority Membership – The configured priority membership grouping.
Bandwidth % – The configured value of bandwidth for the different Priority
Groups.
Max Configurable PGs – The maximum number of Priority Groups that can
be configured.
- OneCommand™ Manager 1
- Application 1
- Version 6.1 1
- User Manual 1
- Table of Contents 3
- Table of Contents 4
- List of Figures 10
- List of Figures 11
- List of Tables 13
- 1. Introduction 14
- Compatibility 15
- Known Issues 16
- Abbreviations 16
- In Windows 18
- In Linux 20
- For RHEL 5 and RHEL 6 type: 21
- In Solaris 22
- In VMware ESX Server 24
- --maintenancemode update 25
- Web Launch Interface 26
- Installation 27
- Solaris: 28
- Linux: 28
- Web Launch Interface Only 29
- /opt/ELXocm/wsuninstall 30
- Manager Application 31
- Launch Interface 32
- Element Definitions 34
- Menu Bar 35
- Toolbar Buttons 35
- Discovery-Tree 37
- Property Tabs 38
- Status Bar 39
- Management Host 40
- 2. Run the following script: 41
- 5. Configuring Discovery 42
- Hosts File 43
- Adding a Single Host 45
- Adding a Range of Hosts 46
- Removing Hosts 48
- Adding Target Portals 52
- Removing a Target Portal 52
- Figure 5-7 iSCSI SNS Tab 53
- Logging into Targets 54
- Removing Targets 55
- Viewing Target Sessions 56
- Session Statistics Area 58
- Connection Information Area 59
- 7. Managing Hosts 61
- Function Summary Area 62
- Grouping Hosts 64
- Managing Host Groups 65
- Creating a Host Group 66
- Deleting a Host Group 66
- Adding a Host to a Host Group 67
- Restoring a Host Group 67
- Restoring all Host Groups 67
- Searching for Hosts 68
- Using CIM 69
- Viewing FC Port Information 71
- Viewing FCoE Port Information 73
- Figure 8-4 Statistics Tab 76
- Firmware Area 83
- WWN Management Area 84
- Mapping Information Area 87
- /usr/sbin/lpfc/lun_scan all 88
- LUN CapacityArea 89
- LUN Masking Area 89
- Current Settings Area 90
- Current Mappings Area 90
- Display Mode Radio Buttons 90
- Target Mapping Buttons 92
- Figure 8-14 LUN Masking Tab 93
- Changing Automapping Settings 95
- Adding a Persistent Binding 95
- Figure 8-18 Maintenance Tab 99
- Creating Virtual Ports 101
- 5x:xx:xx:xx:xx:xx:xx:xx 102
- 10:00:xx:xx:xx:xx:xx:xx 102
- 2x:xx:xx:xx:xx:xx:xx:xx 102
- 3x:xx:xx:xx:xx:xx:xx:xx 102
- Deleting Virtual Ports 103
- Figure 8-22 Virtual Port Tab 104
- Figure 8-24 Reset Warning 107
- Activation Requirements 108
- Setting Driver Parameters 110
- Resetting All Default Values 112
- Parameter Value 112
- DCB Settings Area 118
- CIN Settings Area 119
- DCB Tab Field Definitions 120
- Viewing iSCSI VPD Information 126
- Viewing iSCSI Statistics 127
- Viewing iSCSI LUN Information 131
- Viewing iSCSI PCI Registers 133
- DCBX Settings Area 136
- LLDP Settings Area 137
- PFC Priorities Area 137
- ETS Priority Groups Area 137
- Advanced TCP/IP Configuration 140
- Initiator Login Options Area 142
- Authentication Area 142
- Viewing NIC Port Information 144
- Viewing NIC VPD Information 146
- VPD Table Definitions 147
- Base Host Operating System 153
- Guest Host Information Area 154
- Operating System 155
- OneConnect Adapters 156
- Viewing ASIC Information 158
- Personality Area 160
- License Features Area 160
- Showing Licenses 162
- Installing Licenses 163
- Boot Code Versions Area 166
- PHY Data Field Definitions 169
- Error Rates Area 170
- Counters Area 170
- Module Attributes Area 171
- Diagnostic Data Area 172
- Linux Considerations 173
- Enabling Authentication 173
- DHCHAP Tab 175
- Changing Your Password 177
- 10. Updating Adapter Firmware 178
- Boot Types 183
- Boot Device Parameters 184
- 100 ms 191
- 200 ms 191
- 12. Exporting SAN Information 193
- 13. Diagnostics 194
- Information 195
- Viewing Flash Contents 195
- Viewing Overlay Details 196
- Viewing the PCI Registers 196
- Running a Quick Test 196
- Using Beaconing 197
- Creating Diagnostic Dumps 198
- LightPulse FC HBA Diagnostics 199
- Running Loopback Tests 200
- Loopback Test Combinations 201
- Saving the Log File 203
- OneConnect Diagnostics 204
- FCoE End to End Echo Test 206
- Error Action 206
- Test Cycles 206
- Test Pattern 206
- Test Status 206
- 14. Troubleshooting 211
- Situation Resolution 212
- Application Situations 214
- ./stop_ocmanager 215
- Situations 219
Relacionado con productos y manuales para Software VMware VCENTER APPLICATION DISCOVERY MANAGER 6.1 - REPOSITORY
Software VMware VCM 5.3 - CONFIGURATION MANAGER SECURITY ENVIRONMENT REQUIREMENTS Manual de usuario
(32 paginas)
(32 paginas)
Software VMware VCENTER CONFIGURATION MANAGER 5.3 - SOFTWARE CONTENT REPOSITORY TOOL GUIDE Manual de usuario
(35 paginas)
(35 paginas)
Software VMware VCENTER CONFIGURATION MANAGER 5.3 - SOFTWARE CONTENT REPOSITORY TOOL GUIDE Guía de usuario
(73 paginas)
(73 paginas)
Software VMware NetApp FAS 2050HA Especificaciones
(40 paginas)
(40 paginas)
Software VMware vSphere 4 Guía de usuario
(71 paginas)
(71 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales